Skip to content
BOMproof

BOM · 6 min read

What is a bill of materials and what belongs in it?

A bill of materials (BOM) is the list of all parts, semi-finished products and materials needed to make one product, with the quantity per line. The BOM is the link between design and workshop: purchasing orders from it, production picks and assembles from it, and the drawing refers to it with item numbers.

By , mechanical engineer ·

In short

  • Per line at least: item number, part number, description and quantity
  • A flat list adds everything up, an indented list shows the build-up
  • The EBOM follows the design, the MBOM follows the workshop
  • The BOM should come from the model, not be maintained by hand

What a BOM is for

A drawing shows what something looks like, the BOM says what it is made of. An assembly drawing has balloons with item numbers, and in the BOM you read per item which part it is and how many you need.

The same list is used by different people for different things. That is why it has to be right before it leaves the office.

  • Purchasing: what has to be ordered and how many
  • Production planning: what is made in-house and what is bought
  • Stores and assembly: what has to be picked
  • Costing: what the product costs in material

What is on each line

Which columns you use differs per company. There is an international standard for parts lists on technical drawings (ISO 7573), and many companies also have their own template. These are the columns you come across almost every time in practice.

  • Item number: the reference to the balloon on the drawing
  • Part number or drawing number: unique per part
  • Description or name
  • Quantity, and for material by length or weight also the unit
  • Material, or the standard and size for a standard part (for example ISO 4762 M8×30)
  • Revision of the part
  • Make or buy, often with the supplier or semi-finished product

Link these fields to properties in your CAD model. Then the BOM fills itself and cannot lag behind the design.

Flat or indented

A flat BOM lists each part once with the total quantity in the whole product. Handy for purchasing, but you no longer see which assembly something is in.

An indented (or multi-level) BOM shows the build-up: main assembly, subassemblies and the parts below them. The quantity per line then applies per parent assembly. If a subassembly occurs twice, you need twice as many of every part below it.

That multiplying is exactly what often goes wrong: if you add up an indented list as if it were flat, you order too few.

EBOM and MBOM

The engineering BOM (EBOM) follows the design as it is in the model. The manufacturing BOM (MBOM) follows the way the product is made in the workshop, with operations, semi-finished products and consumables such as welding wire and paint added.

The two should connect, but they are not the same. A BOM for production is therefore almost always derived from the engineering BOM.

Where it goes wrong in practice

Most errors in a BOM do not arise while designing, but afterwards: when copying, updating and sending it on.

  • The list was updated by hand and lags behind the model
  • Quantities in an indented list were not multiplied
  • The same standard part is in it under two different descriptions
  • A part has no material or a default material
  • The revision level in the list differs from the drawing or the model
  • Formulas in Excel point to the wrong cell after sorting or inserting rows

How to keep a BOM reliable

Two agreements prevent most of the work afterwards.

  1. 1 Let the BOM come from the model, and when something is wrong change the model, not the list.
  2. 2 Export model, drawing and BOM at the same moment and put them side by side before release.

With BOMproof

This work automatically, at every release.

BOMproof puts your STEP model, your PDF drawings and your Excel BOM side by side and points out every deviation: with a pin in the 3D model and a balloon on the drawing. You tick off what is correct.

Method and corrections

This guide describes in our own words how we carry out a check ourselves. We refer to standards by number; the literal text of the standard is not reproduced here, because it is protected by copyright. Found a mistake? Email info@bomproof.nl: we correct it within a week and put the new date at the top.

Frequently asked questions

What is a BOM.

01 What is the difference between a BOM and a parts list?

In practice the terms are used interchangeably. A parts list usually names only the parts, a BOM also the semi-finished products, materials and the build-up of the product.

02 What does BOM stand for?

Bill of materials. You also come across EBOM (engineering) and MBOM (manufacturing).

03 How do I get a BOM out of my CAD model?

Almost every CAD package can export a BOM to Excel or CSV, often from the drawing. If you only have a STEP file, you can also get the parts and quantities from that: this site has a free tool that does it in your browser.

04 Does a standard part such as a bolt or nut belong in the BOM?

Yes. Standard parts have to be ordered and assembled, so they are in it with standard, size, length and property class. Describe them the same way everywhere, otherwise you count the same part twice or miss it.

05 Is there a BOM template for Excel?

Yes, this site has a free template with the columns from this article. Per line you enter the level and the quantity per assembly; Excel calculates the totals and the flat list for purchasing itself.

Ready for your first automated check?

Book a 30-minute demo. Bring one of your own designs and see live how BOMproof checks it.