Standard part · ISO 4017
Hex head screw ISO 4017 / DIN 933
The dimensions of fully threaded hex head screws from M3 to M24 in one table: width across flats per ISO 4017 and the old DIN 933, head height, clearance hole and tap drill. Every size also has its own page with a drawing.
Dimension table
All dimensions in mm
| Size | Pitch P | s ISO | s DIN 933 | k | a max | Hole fine | Hole medium | Tap drill |
|---|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 5.5 | 2 | 1.5 | 3.2 | 3.4 | 2.5 |
| M4 | 0.7 | 7 | 7 | 2.8 | 2.1 | 4.3 | 4.5 | 3.3 |
| M5 | 0.8 | 8 | 8 | 3.5 | 2.4 | 5.3 | 5.5 | 4.2 |
| M6 | 1 | 10 | 10 | 4 | 3 | 6.4 | 6.6 | 5 |
| M8 | 1.25 | 13 | 13 | 5.3 | 3.75 | 8.4 | 9 | 6.8 |
| M10 | 1.5 | 16 | 17 | 6.4 | 4.5 | 10.5 | 11 | 8.5 |
| M12 | 1.75 | 18 | 19 | 7.5 | 5.25 | 13 | 13.5 | 10.2 |
| M16 | 2 | 24 | 24 | 10 | 6 | 17 | 17.5 | 14 |
| M20 | 2.5 | 30 | 30 | 12.5 | 7.5 | 21 | 22 | 17.5 |
| M24 | 3 | 36 | 36 | 15 | 9 | 25 | 26 | 21 |
s is the width across flats, k the nominal head height, a max = 3 × P. Clearance hole to ISO 273, tap drill = d minus P, rounded to the usual drill size. For M10 and M12 the width across flats differs between ISO 4017 and DIN 933.
The letters
What the dimensions mean
- d: nominal thread diameter (M8 = 8 mm).
- P: pitch of the coarse thread.
- s: width across flats, the distance between two flat sides: the size of your spanner.
- k: head height.
- a: maximum length under the head without full thread (3 × P).
- l: length of the screw, measured without the head.
Per size
Drawing and dimensions per screw
Questions
Frequently asked questions about hex head screws
01 What is the difference between DIN 933 and ISO 4017?
DIN 933 was withdrawn and replaced by ISO 4017. Thread and head height are the same, but for M10 and M12 the width across flats differs: 17 and 19 mm for DIN 933, 16 and 18 mm for ISO 4017. If both appear in your BOM, they really are different parts.
02 What is the difference between ISO 4017 and ISO 4014?
ISO 4017 (formerly DIN 933) is the hex head screw threaded up to the head. ISO 4014 (formerly DIN 931) has an unthreaded shank under the head.
03 Which lengths are standard?
ISO 4017 lists standard lengths from 2 × d (rounded to a standard length) to 10 × d, with a maximum of 200 mm. For M8 that is 16 to 80 mm.
Checked against
- ISO 4017:2022, tabel 1 en 2 (inkijkexemplaar)
- Reyher: Technische Informationen (ISO 4017 ersetzt DIN 933)
- fasten.it: DIN 933 (1987)
- neue-physik.de: Durchgangslöcher (DIN EN 20273)
- Albany County Fasteners: clearance holes ISO 273
- Optimas: tapping sizes
Every dimension on this page was checked on 15 November 2026 against at least two of these sources.
For a critical application, always check the dimensions in the standard or with your supplier.
Is this screw in your BOM twice?
Put model, drawing and BOM side by side and see per position what doesn't match.