Standard part · ISO 4032
Hex nut ISO 4032 / DIN 934
The dimensions of the regular hex nut from M3 to M24 in one table: width across flats and height per ISO 4032 and the old DIN 934, and the clearance hole for the bolt. Every size also has its own page with a drawing.
Dimension table
All dimensions in mm
| Size | Pitch P | s ISO | s DIN 934 | m ISO | m DIN 934 | Hole fine | Hole medium |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 5.5 | 2.4 | 2.4 | 3.2 | 3.4 |
| M4 | 0.7 | 7 | 7 | 3.2 | 3.2 | 4.3 | 4.5 |
| M5 | 0.8 | 8 | 8 | 4.7 | 4 | 5.3 | 5.5 |
| M6 | 1 | 10 | 10 | 5.2 | 5 | 6.4 | 6.6 |
| M8 | 1.25 | 13 | 13 | 6.8 | 6.5 | 8.4 | 9 |
| M10 | 1.5 | 16 | 17 | 8.4 | 8 | 10.5 | 11 |
| M12 | 1.75 | 18 | 19 | 10.8 | 10 | 13 | 13.5 |
| M16 | 2 | 24 | 24 | 14.8 | 13 | 17 | 17.5 |
| M20 | 2.5 | 30 | 30 | 18 | 16 | 21 | 22 |
| M24 | 3 | 36 | 36 | 21.5 | 19 | 25 | 26 |
s is the width across flats, m the maximum nut height. Clearance hole to ISO 273 for the bolt. For M10 and M12 the width across flats differs between ISO 4032 and DIN 934; from M5 the ISO nut is higher. ISO 4032:2023 covers M5 to M39 in its main tables; M3 and M4 come from the previous edition (1999).
The letters
What the dimensions mean
- d: nominal thread diameter (M8 = 8 mm).
- P: pitch of the coarse thread.
- s: width across flats, the distance between two flat sides: the size of your spanner.
- m: height of the nut (maximum).
Per size
Drawing and dimensions per nut
Questions
Frequently asked questions about hex nuts
01 What is the difference between DIN 934 and ISO 4032?
DIN 934 is withdrawn and replaced by ISO 4032. The thread is the same, but from M5 the ISO nut is higher (M8: 6.8 versus 6.5 mm) and for M10 and M12 the width across flats differs: 17 and 19 mm for DIN 934, 16 and 18 mm for ISO 4032.
02 Which nut property class goes with an 8.8 bolt?
A class 8 nut. A higher class is fine as well, a lower one is not. A 10.9 bolt likewise takes a class 10 nut.
03 Can I mix ISO and DIN nuts?
The thread fits, but they are different items: the height differs from M5 and for M10 and M12 you need a different spanner. So pick one standard per size in your BOM.
Checked against
- ISO 4032:2023, tabel 1 en 2 (inkijkexemplaar)
- ISO 4032:1999, tabel 1 (inkijkexemplaar)
- Reyher: Technische Informationen (ISO 4032 ersetzt DIN 934)
- KIPP: Sechskantmuttern DIN 934 / ISO 4032 (datasheet)
- BOLTS: DIN 934
- neue-physik.de: Durchgangslöcher (DIN EN 20273)
- Albany County Fasteners: clearance holes ISO 273
Every dimension on this page was checked on 15 November 2026 against at least two of these sources.
For a critical application, always check the dimensions in the standard or with your supplier.
Is this nut in your BOM twice?
Put model, drawing and BOM side by side and see per position what doesn't match.